( pages, 2.3 MB PDF) February Timber tongue and groove decking is a specialty lumber product, constituting an important part of modern timber

TONGUE AND GROOVEROOF DECKINGAmericanForest & PaperAssociationBy downloading any file to your computer, you are accepting and agreeing

The IBC doesn t recognize 2x tongue and groove decking (we have capacities and manually calculate diaphragm shear capacities from them

Tongue and groove edges, panel edge clips (one midway between each support, except two equally Nail type, size and spacing may vary for engineered diaphragm designscSee Table 6, page , Load carrying capacity is highest.

Standard for Tongue and Groove Roof Decking, AITC 72 ft minimum end joint spacingFigure 7Controlled Random Layup(Two inch decking).

High Load Diaphragm Two Layer Panelized ConstructionDiaphragm No2 est 5 plf), limited by shear capacity at interior panel jointsNote that the shear

SUBDIAPHRAGMA portion of a larger wood diaphragm and wall sheathing, subflooring, diaphragms and built up members) beveled, tongue and groove or U shaped joints ity, torsional moment capacity and deflection characteris .

Feb 4, 5.1.2.2.1 Tongue Groove Single Straight Sheathed Diaphragms 5.1.2.2.2 Square Edged Single Straight Sheathed Diaphragms .

Sep , Mechanically Laminated or Tongue Groove IBC .2 applies to wood framed diaphragms and Example capacities are:.

increase the diaphragm stiffness and shear capacity by attaching a steel truss system to MAE 1: Tongue and groove sheathed diaphragm JOURNAL

( pages, 2.3 MB PDF) February Timber tongue and groove decking is a specialty lumber product, constituting an important part of modern timber

TONGUE AND GROOVEROOF DECKINGAmericanForest & PaperAssociationBy downloading any file to your computer, you are accepting and agreeing

The IBC doesn t recognize 2x tongue and groove decking (we have capacities and manually calculate diaphragm shear capacities from them

Tongue and groove edges, panel edge clips (one midway between each support, except two equally Nail type, size and spacing may vary for engineered diaphragm designscSee Table 6, page , Load carrying capacity is highest.

Standard for Tongue and Groove Roof Decking, AITC 72 ft minimum end joint spacingFigure 7Controlled Random Layup(Two inch decking).

High Load Diaphragm Two Layer Panelized ConstructionDiaphragm No2 est 5 plf), limited by shear capacity at interior panel jointsNote that the shear

SUBDIAPHRAGMA portion of a larger wood diaphragm and wall sheathing, subflooring, diaphragms and built up members) beveled, tongue and groove or U shaped joints ity, torsional moment capacity and deflection characteris .

Feb 4, 5.1.2.2.1 Tongue Groove Single Straight Sheathed Diaphragms 5.1.2.2.2 Square Edged Single Straight Sheathed Diaphragms .

Sep , Mechanically Laminated or Tongue Groove IBC .2 applies to wood framed diaphragms and Example capacities are:.

increase the diaphragm stiffness and shear capacity by attaching a steel truss system to MAE 1: Tongue and groove sheathed diaphragm JOURNAL

(a) Tongue and groove edges, panel edge clips (one midway between each PER FOOT) FOR HORIZONTAL LP PANEL DIAPHRAGMS WITH FRAMING OF

diaphragm, resisting wind and seismic loadstongue and groove edges 1These loads represent the load carrying capacity of the panels spanning

ing, roof and wall sheathing, subflooring, diaphragms and built up members), shall conform beveled, tongue and groove or U shaped joints.1.5.2 Roof

systems, diaphragms and shear walls, fire rated systems (d) Most tongue and groove panels are manu factured with a 1 2 inch net face width, although

Tongue and groove plank wood decking is a product that is commonly used in post to investigate their failure mode characteristics and to quantify their capacityPlacing sheathing on top of a decking system to create a diaphragm action

such as tongue and groove panelingrate the structural benefits of structural insulated panels (SIPs) as diaphragm sisting capacity of .0 kN (3, lb.).

weight for their capacity ratingsEngineered with tongue and groove design allowing for Diaphragm accuracy for higher capacity metering applications.

Two nails per board are required for tongue and groove sheathingDiaphragm values associated with this construction is outside the scope of this report.

Reinforced Masonry Bearing Wall Buildings with Flexible Diaphragms: RM1: diaphragms consist of straight or diagonal lumber sheathing, tongue and groove planks, of the frame and the moment capacity of the beam column connections.

Lock Deck™ can be engineered to carry diaphragm shear forces from earthquake is applied on top of the tongue and groove joint between adjacent